Parts & Accessories

Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required

Replacement axles for Manitou forks

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

Salsa's Ti Flip-Offs are as beautiful to the touch as they are to the eye. Lightweight. Smooth. Recommended for road use or rigid front mountain bike use only. Available in a whole host of colors. - Beautifully machined and hand-friendly - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 44g

Replacement clear plastic spoke guard.

Replacement Axle nuts for three speed Sturmey Archer hubs.

- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install

- Replacement rear skewer - Spacing: 135mm - Material: Steel

- Variable widths - Left: 32mm - Center: 52mm - Right: 36mm - Length: 120mm - Overall: 141mm

• 5mm skewer set (F+R hubs) • Standard 5mm Hex release • Black or Silver anodized finish • Chromoly axles

- Replacement steel quick release skewers

• Replacement aluminum quick release skewers

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

The Muc-Off Ultimate Tubeless Kit contains everything needed to get a tubeless-ready wheelset set up and ready to roll. Each Kit contains Tubeless Rim Tape, two CNC-machined black tubeless valves and two pouches of No Puncture Hassle Tubeless Sealant.

This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Salsa's Stainless Flip-Offs use stainless steel rods for corrosion-resistant strength. They're strong, lightweight, and gorgeous. - Recommended for front rigid fork or full suspension use - Beautifully machined and hand friendly - Variety of sizes, sold as pairs or individually, front or rear - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 49g

CushCore is an engineered foam insert to be mounted inside a tire, designed to absorb impacts, reduce vibration, and increase lateral stability. These characteristics translate to a more controlled, comfortable, and faster ride. - The system is designed to be used with tubeless-ready or tubeless converted rims and tires and is compatible with tubeless tire sealants - A specially designed tubeless air valve is included with each insert; allowing air to move through the valve without becoming obstructed by the insert - The insert divides the inner volume of the tire in half, maintaining air underneath the tread and the foam insert next to the rim - Fits tire widths 2.1 – 2.6" and rims with internal width 22 – 35mm Includes: - 2 CushCore Inserts - 2 CushCore Tubeless Air Valves - 4 Rim Stickers - Installation Instructions

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 9mm x 1, front "parallax" style hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 11.0mm - 1 cone per bag COMPATIBLE HUBS: - JoyTech 9mm x 1, front "parallax" style hub - Taiwanese hubs with 9mm x 1 axle

The Drive Thru is a dummy hub or chain keeper that replaces your wheel while cleaning the chain. It is a fast and effective way to clean your chain between races or in your garage. It allows you to fully rotate your cranks and shift through your complete range of gears while protecting the frame. Installs simply with one hand, and is quick and easy to change between bikes. The Drive Thru is also great for packing the bike for transport. *This Drive Thru Value Meal includes three dummy axles with 1.0, 1.5 and 1.75 thread pitches and one pulley. - Value Meal includes 1.0, 1.5, and 1.75mm thread pitch dummy axles. - All Drive Thru dummy axles are 12mm in diameter. - Dummy axles are precision machined from 7075 aluminum and knurled for easy grip. - Pulleys are machined from durable Delrin. - Oil and solvent resistant O-rings - Lead-in threads designed for quick insertion into the frame - Simple, one-handed installation (no tools required)

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm

Lightweight quick release lever with a classic aesthetic. - Weight: 39g

Rear Thru Axle conversion kit for Go-Devil Hubs - Converts QR to 142x12mm thru (axle not included)

- High-quality fat bike rim strips - Super durable PVC material

Elite Series skewers for fat bike applications AL6061 alloy lever with CrMo axle Available for 135mm, 150mm, 170mm, and 190mm OLD spacing

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3